 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| TB9000AFG TOSHIBA BiCMOS Integrated Circuit Silicon Monolithic TB9000AFG 5 V Voltage Regulator with Watchdog Timer The TB9000AFG is an IC specially designed for microcomputer systems in automobiles. It features low standby current and various system reset functions. With an external pass Tr., the TB9000AFG can supply a high output current. A current limiter function is incorporated as a protective function. System reset includes low-voltage reset, power-on reset, and watchdog timer functionality. Weight: 0.14 g (typ.) Features * * * * * * Accurate output: 5.0 V 0.15 V Low current consumption: 120 A (VIN = 12 V, Ta = 25C) at 5 V output + reset timer Reset functions: Low-voltage reset/power-on reset/watchdog timer Current limiter: Adjustable with external resistor Operating temperature: -40 to 125C Small SMD package: SSOP-16-pin About solderability, the following conditions were confirmed. Solderability (1) Use of Sn-37Pb solder Bath solder bath temperature = 230C dipping time = 5 seconds the number of times = once use of R-type flux (2) Use of Sn-3.0Ag-0.5Cu solder Bath solder bath temperature = 245C dipping time = 5 seconds the number of times = once use of R-type flux 1 2007-03-26 TB9000AFG Block Diagram & Pin Layout NC 16 NC 15 WS 14 CK 13 NC 12 TC 11 NC 10 RESET 9 Watchdog timer Power on reset Vref Comp Current limiter 0.3 V 5 V Reg Amp 70 k 1 VIN 2 NC 3 VS 4 OUT 5 COMP 6 Vcc 7 NC 8 GND Note: Some functional blocks, circuits, or constants are omitted or simplified in the block diagram to clarify the descriptions of the relevant features. 100 k 2 2007-03-26 TB9000AFG Pin Description Pin No. 1 Symbol VIN Description Power supply input pin. It contains a current limiter and startup circuit. Detection pin for the VCC current limiter. Any voltage drop occurring in the external resistor RS between pins VIN and VS is monitored. The current limiter is actuated when the voltage drop exceeds 0.3 V. Ex.) When the current limiter need to be actuated at a load current of 600 mA: RS = 0.3 V/600 mA = 0.5 . This pin is used to connect the base of an external PNP transistor. The output voltage is controlled by an internal op-amp to maintain it stably at 5 V. Since the recommended IOUT current is 8 mA, an output current of 600 mA can be run if HFE of the external transistor is 80 or more. Phase-compensating pin for VCC. Connect a phase-compensating capacitor between pin VCC and this pin. Voltage detection pin for the 5 V constant-voltage power supply, VCC. It also supplies power to the reset timer circuit. Grounded Reset output pin for power-on reset and watchdog timer. Generates a reset signal that is determined by CT at the TC pin. If no clock is fed to the CK input, this pin generates a reset pulse intermittently. This is an N-MOS drain output with a 100 k pull-up resistor to VCC. Time setup pin for the reset and watchdog timers. Connect capacitor CT to GND. The time is set up by internal constant current. Clock input pin for the watchdog timer. This pin detects the rising edge of the input signal and does not require external coupling capacitor. Watchdog timer function ON/OFF control pin. Set to LOW for active mode and HIGH for inactive mode. Not connected. (Electrically, this pin is completely open.) 3 VS 4 OUT 5 6 8 COMP VCC GND 9 RESET 11 TC 13 CK 14 2, 7, 10, 12, 15, 16 WS NC 3 2007-03-26 TB9000AFG Functional Description The TB9000AFG incorporates a constant-voltage 5 V power supply function to feed stable power to the CPU, while the system reset and CPU monitor functions ensure stable operation of the CPU, etc. These functions are explained below. (1) Constant-Voltage 5 V Power Supply Function This constant-voltage function has a reference voltage Vref in the IC that is insusceptible to temperature changes and input voltage fluctuations. The power supply circuit is designed in such a way that this voltage is stepped up to 5 V by using an OP amp and a voltage-dividing resistor. The OP amp, dividing resistor and an output transistor connected to the OP amp output together configure a closed loop. An overcurrent protection function is incorporated as a protective measure in case a fault such as shorting to GND occurs in the 5 V output. A current detecting resistor is inserted between the VIN and the VS pins, and a voltage drop across this resistor is detected by a comparator, thereby suppressing the operation of the OP amp to ensure that the voltage drop will not exceed 0.3 V. In this way, a current limiter function is actuated to prevent any more current from flowing. (2) System Reset Function (see Timing Charts) Voltage monitoring function When powered on, the power-on reset timer starts counting the moment the voltage VCC applied to the CPU exceeds VTH. When powered off, this voltage monitoring function outputs a reset signal immediately when VCC drops below VTH. A reset signal is also output immediately when VCC drops for some reason during normal operation. Then, when VCC is restored to the normal voltage and exceeds VTH, the power-on reset timer starts counting. The reset signal is output from the RESET pin. Power-on reset timer function To allow the 5 V constant voltage to stabilize at power-on, as well as provide sufficient time for the clock oscillation in the CPU to stabilize, the device remains reset for a predetermined time before being released from the reset state. The duration of this time can be set as desired by choosing appropriate values for the external capacitor connected to the TC pin. The system starts charging the capacitor when the VCC voltage exceeds VTH. When this charge voltage exceeds 4 V, the capacitor is discharged by the IC's internal transistor. When the capacitor is discharged down to 2 V, the reset signal is inverted to deactivate the reset. Watchdog timer function Program your system to output a clock each time one program routine is finished in the CPU system software, and input this clock to the CK pin of the IC. The IC's TC pin is repeatedly charged and discharged between 2 V and 4 V. However, when a clock is input, it switches over and starts discharging in the middle of charging and then starts charging from 2 V again. Since the clock is generated at predetermined intervals when the CPU system is operating normally, the TC pin switches over and starts discharging before the charge voltage reaches 4 V. However, if no clock is input while being charged from 2 V to 4 V, the clock is assumed to have stopped, i.e., the CPU system has gone wild, so that a reset signal is output to reset the CPU system. Watchdog timer stop function The watchdog timer can be switched ON or OFF by use of the WS pin. If the WS pin is fixed to LOW, the watchdog timer will be active. (See Timing Chart 1.) If the WS pin is fixed to HIGH, the watchdog timer will be inactive. (See Timing Chart 2.) When the WS pin is fixed to HIGH, no reset signal is output, in which case only the power-on reset timer is useful. Note: The overcurrent protection feature is intended only to protect the IC from a temporary short circuit. A short circuit over an extended period of time may place excessive stress on the IC, possibly causing it to be damaged. The system must be configured so that any overcurrent condition will be eliminated as soon as possible. 4 2007-03-26 TB9000AFG Timing Chart 1: WS = LOW Timing Chart 2: WS = HIGH Note 1: Definitions of symbols used in this timing chart are provided in the Electrical Characteristics table. Note 2: Timing charts may be simplified to clarify the descriptions of features and operations. 5 2007-03-26 TB9000AFG Absolute Maximum Rating (Ta = 25C) Characteristics Symbol VIN1 Input voltage VIN2 VIN3 Output current IOUT1 IOUT2 Output voltage Operating temperature Storage temperature VOUT1 VOUT2 Topr Tstg Pin VIN, VS VCC CK, WS, TC OUT RESET OUT RESET Rating 45 (1 s) 6.0 VCC 10 mA 5 45 (1 s) V VCC V Unit - - -40 to 125 -55 to 150 C C Note: The absolute maximum ratings of a semiconductor device are a set of specified parameter values that must not be exceeded during operation, even for an instant. If any of these levels is exceeded during operation, the device's electrical characteristics may be irreparably altered and the reliability and lifetime of the device can no longer be guaranteed, possibly causing damage to any other equipment with which it is used. Applications using the device should be designed so that the absolute maximum ratings will never be exceeded in any operating conditions. Ensuring that the parameter values remain within these specified ranges during device operation will help to ensure that the integrity of the device is not compromised. 6 2007-03-26 TB9000AFG Electrical Characteristics Characteristics (Unless otherwise specified, VIN = 6 to 16 V, ILOAD = 10 mA, Ta = -40 to 125C) Symbol Pin Test Circuit Test Condition Ta = -40 to 105C Ta = -40 to 125C VIN = 6 to 40 V ILOAD = 1 to 300 mA Min 4.85 4.82 Typ. 5.0 5.0 0.1 0.2 0.01 Max 5.15 5.15 0.5 1.0 % % %/C V Unit Output voltage Line regulation Load regulation Temperature coefficient Output voltage Output leakage current Input current Input current Input current Input voltage VREG VLINE VLOAD VCC VCC VCC VCC RESET RESET TC CK WS CK - - - - - - - - - - V - - - - VOL ILEAK IIN IIN IIN VIH VIL VIH - 0.3 5 IOL = 2 mA VIN( RESET ) = VCC VIN(TC) = GND VIN(CK) =0 VCC VIN(WS) =0 VCC - - - -5 -5 0.8 VCC - - -10 - - - - - - 0.3 120 120 4.2 0.80 400 x CT 200 x CT 8.0 x CT A A A A V - 5 5 - 0.2 VCC - 0.8 VCC Input voltage VIL Current limiter detection VLIMIT WS VIN, VS - - Ta = 25C, VIN = 12 V - 0.2 VCC 0.375 170 - 0.225 V V - - 4.0 Current consumption ICC VTH - - Ta = -40 to 125C, VIN = 12 V A 190 4.4 V 1.15 520 x CT 260 x CT 12.0 x CT ms ms ms Reset detection voltage VTH TPOR TWD TRST Tw VCC - - - - - VCC - VTH 0.45 280 x CT 140 x CT 4.0 x CT 3 Power-on reset Watchdog timer Reset timer Clock pulse width RESET RESET RESET CK - - s Note 1: CT is measured in units of F. Note 2: The specification values for power-on reset, watchdog timer and reset timer above are guaranteed only for the IC itself. Any practical application of the IC should take into account fluctuations in the CT value. Note 3: For the above current consumption ICC, it is specified that ILOAD = 0 mA. Operating Conditions Part Name CT Min 0.01 Typ. 0.25 Max 10 Unit F 7 2007-03-26 TB9000AFG Reference Characteristics Input - Output Characteristics RESET Output Characteristics 6 6 (V) (V) VRESET 4 4 VCC 2 2 0 0 2 4 6 0 0 2 4 6 VIN (V) VCC (V) Current Limiter Characteristics 7 6 5 (V) 4 VCC 3 2 1 0 0 0.1 0.2 0.3 0.4 VLIMIT (V) 8 2007-03-26 TB9000AFG Example of Application Circuit RS 5.0 V VDD VB 10 F 10 F 5V monitor C1 VIN VS Current limiter OUT COMP VCC CPU Constant voltage TB9000AFG RESET TC Reset timer CK WS GND RESET Po1 Caution for Wiring Note 1: C1 and C2 are for absorbing disturbances, noise, etc. C3 is for phase compensation. Connect each capacitor as close to the IC as possible. Note 2: Ensure that the IC is mounted correctly. Failure to do so may result in the IC or target equipment being damaged. Note 3: The application circuit shown above is not intended to guarantee mass production. A thorough evaluation is required when designing an application circuit for mass production. CT 470 pF C3 C2 9 2007-03-26 TB9000AFG Package Dimensions Weight: 0.14 g (typ.) 10 2007-03-26 TB9000AFG RESTRICTIONS ON PRODUCT USE * The information contained herein is subject to change without notice. 021023_D 070313EBA_S * TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc. 021023_A * The TOSHIBA products listed in this document are designed and manufactured for usage in automotive electronic equipment. These TOSHIBA products are neither intended nor warranted for usage in equipment other than automotive electronic equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage includes atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. TOSHIBA products listed in this document shall not be used for other than automotive electronic equipment such as the applications listed above. 070313_AG * The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. 060106_Q * The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. 070122_C * The products described in this document are subject to foreign exchange and foreign trade control laws. 060925_E 11 2007-03-26 |
Price & Availability of TB9000AFG
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |